HOW TO READ ERROR CODES ON FRIGIDAIRE AFFINITY WASHER

To read the error codes on a Frigidaire Affinity washer, you will have to enter diagnostic mode. The following instructions explain how to do that.

Start by pressing any button on the control panel to wake the washer control. Wait 5 seconds, then press and HOLD the Start/Pause and Cancel buttons simultaneously.

As long as you are holding down the buttons, the failure code will appear in the display as an E followed by two numbers, a number and a letter or two letters. The
control will beep, and the Door Lock, Wash, Rinse, and Final Spin indicator lights will flash.

HOW TO CLEAR ERROR CODES ON FRIGIDAIRE AFFINITY WASHER

To clear the latest stored error code:
• Turn the Program Knob to the start position of the cycle furthest to the left.
• Press Start/Pause to start the cycle and save it.
• Press Cancel to stop the cycle and turn off the LEDs.
• Press Cancel again to turn on the LEDs.
• Within 5 seconds, press and hold the Option and Start/Pause buttons until LEDs start sequentially chasing, then release buttons.
• Turn the program knob clockwise seven clicks from the Start Position. The control will signal the last error code.
• Press and hold the Options and Start/Pause buttons for 3 seconds. The error clears from memory.
• Exit Diagnostic Mode to return the washer to regular operation.
a) Unplug the power cord, wait 5-8 seconds, then reconnect the power cord OR
b) Turn the program knob clockwise 2 or 3 clicks after the Start Position. Press Options and Start/Pause buttons together for a few seconds
until wash cycle LEDs appear.

If you have any questions about how to read error codes on Frigidaire Affinity washer, you can write to us in chat.

FRIGIDAIRE AFFINITY WASHER ERROR CODES

If you need more information or help with repairing any of the error codes listed below, feel free to ask for help in chat.

E11 Fill time too long.
E13 Water leak in tub or air leak in air bell.
E21 Water is not pumping out fast enough.
E23 Drain pump relay on control board failed, wire off-pump or pump Replace console control board, cable or defective pump.
E24 Drain pump relay on the control board failed. Replace the console control board.
E31 Pressure sensor not communicating with the control board.
E35 Pressure sensor indicates water overfill.
E36 Console control board problem. Replace the console control board.
E38 Air chamber clogged or pressure sensor defective. Check the air chamber, replace the water level pressure sensor.
E41 Control board thinks the door switch is open.
E43 Console control board thinks the door locking device has failed.
E44 Console control board problem. Replace the console control board.
E45 Console control board problem. Replace the console control board.
E46 Console control board problem. Replace the console control board.
E47 Console control board thinks the door PTC circuit is open in the spin.
E48 Console control board thinks the door PTC circuit is closed.
E52 Bad signal from tacho generator.
E56 High motor current.
E57 High current on the inverter.
E58 High current on motor phase.
E59 No tacho signal for 3 seconds.
E5A High temperature on heat sink caused by overloading.
E5B High temperature on the heat sink. Replace the speed control board.
E5C High temperature on the heat sink. Replace the speed control board.
E5D Communication problem.
E5E Communication problem.
E5F Communication problem.
E66 Heating element relay failure.
E67 Input voltage on microprocessor incorrect.
E68 Current leakage to ground on heater or fuse opened.
E71 Wash NTC failure.
E74 Wash temperature does not increase. Wire off NTC – replace the water valve.
E75 Water temperature sensor circuit.
E82 Console control board problem. Replace the console control board.
E83 Console control board problem. Replace the console control board.
E91 Communication error between the UI board and the console control board.
E93 Console control board problem. Replace the console control board.
E94 Console control board problem. Replace the console control board.
E95 Communication error. Replace the console control board.
E97 Console control board problem. Replace the console control board.
E98 Console control board problem. Replace the console control board.
EB1 Incoming power frequency out of limits.
EB2 Incoming line voltage above 130 VAC. Check voltage at the outlet. If < 130VAC,
replace the console control board.
EB3 Incoming line voltage below 90 VAC. Check voltage at the outlet. If > 90VAC,
replace the console control board.
EBE Console control board problem. Replace the console control board.
EBF Console control board problem. Replace the console control board.
EF1 Clogged drain pump. Unclog the drain pump.
EF2 Too much soap.