October 14, 2024

Troubleshooting the Whirlpool Range F9E0 Error Code

Whirlpool Range F9E0 Error Code

The Whirlpool Range F9E0 Error Code indicates an issue with the power supply to the range. This could be due to incorrect wiring in either the house or the range itself. Fortunately,  it’s something you can often troubleshoot yourself by following the steps listed below.

Step 1: Enter Diagnostics Mode:

The first step in troubleshooting your Whirlpool Range F9E0 error code is to enter the Diagnostics Mode. This can be done by pressing the CANCEL button twice, followed by the START button. This sequence allows you to verify the failure. If the displayed failure matches the F9E0 error code, proceed to the next step.

Step 2: Disconnect Power:

Safety first! Before proceeding with any troubleshooting, ensure that your range is disconnected from the power source. This can be done by simply unplugging the range.

Step 3: Verify House Power Supply:

The F9E0 error code can often be caused by an incorrect house power supply. You need to verify that your house power supply provides 240 VAC between L1 and L2, and 120 VAC between L1 and N and L2 and N. If these values are not correct, it’s time to call a qualified electrician. If the voltage measurements are correct, you can move on to the next step.

Step 4: Check Wiring at the Range Terminal Block:

Next, you’ll need to ensure that the electric supply is correctly wired at the range terminal block. Incorrect wiring can often lead to the F9E0 error code on your Whirlpool Range.

Step 5: Check the Resistance of the Bake Element:

The resistance of the Bake element should be around 16 ohms. If it’s not, the Bake element will need to be replaced.

The resistance of an electrical element can be calculated using Ohm’s law, which states that resistance (R) equals voltage (V) squared divided by power (P). In the United States, the standard voltage for appliances like a range is 240 volts.

Since the typical bake element on these ranges are around 3600 watts, the resistance would be calculated as follows:

R = V^2 / P R = 240^2 / 3600 R = 57600 / 3600 R = 16 ohms

So, the resistance of a 3600 watt bake element on a range should be approximately 16 ohms. Please note that this is an approximation and actual values may vary based on specific models and manufacturers.

Step 6: Replace All Parts and Panels:

Before operating the range, make sure to replace all parts and panels. This is a crucial safety measure to prevent any accidents.

Step 7: Reconnect Power:

Now that you’ve completed the troubleshooting steps, you can reconnect the range to the power source by plugging it back in.

Step 8: Verify Normal Operation:

Check if the range is operating normally. If it is, you’ve successfully troubleshooted the F9E0 error code.

Step 9: Clear Error Codes:

Finally, to clear any error codes, enter the Diagnostics Mode again by pressing CANCEL, CANCEL, START.

Step 10: Replace the Control Board

If steps 1-9 all check out ok, replace the main control board. If you need the part number for the control board for your range, get the full model number of your range and ask us in our Appliance Part Questions Forum or chat with parts specialists over at PrismParts.com.

Whirlpool Range F9E0 Error Code Repair Help

Experiencing an F9E0 error code on your Whirlpool Range can be a bit of a challenge, but don’t worry, we’re here to help. Like state previously this error code typically indicates a miswired house or range, and while it can often be resolved through a series of troubleshooting steps, we understand that it can be daunting to tackle on your own. That’s why we’ve created the Range Repair Questions Forum – a forum where you can ask questions and get help with your Whirlpool Range F9E0 error code. Our community of experts are always ready to provide insights, share experiences, and guide you through the repair process. So, don’t hesitate to reach out and ask your questions in our forum – we’re here to help you get your range back to working order.

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.